- All Products
- Shop by Brands
- BW Technologies
- BW Technologies
- BW Technologies Monitors
- Models
- BW Clip
- BW Clip4
- GasAlertClip Extreme
- GasAlert Extreme
- GasAlertMicroClip XT
- GasAlertMicroClip XL
- GasAlertMicroClip X3
- GasAlertQuattro
- GasAlertMax XT II
- GasAlertMicro 5 Series
- SamplerPak
- IntelliDox Docking System
- MicroDock II
- BW Ultra
- BW Solo
- Gas Monitors
- Gas Monitor Manufacturers
- BW Technologies
- Bacharach
- Biosystems
- Crowcon
- Gas Clip Technologies
- GfG Instruments
- GMI/Detcon
- Honeywell Analytics
- Industrial Scientific
- MSA
- RAE Instruments
- RKI Instruments
- Calibration Gas
- Combustion Analyzers
- Water Quality
- Reliability Instruments
- Refractometers
- HVAC
- Weather
- Temperature
- Laboratory
- Sound
- IAQ
- Electrical
- All Categories
Extech VT10 Multifunction Voltage Tester
Item #:
EXT-VT10
Brand:
Extech
Share this product:
VT10 Multifunction Voltage Tester by Extech
Features
- LED AC/DC voltage indication: AC: 24, 48, 120, 208, 240, 277, 480, 600; DC: 6, 12, 24, 36, 48, 110, 220, 400
- Polarity detection with LEDs for positive and negative DC
- Two handed operation for low impedance testing
- Built-in flashlight for testing in tight areas
- Rubberized double-molded IP64 housing
- Meets EN61243-3 safety rating
- Dimensions: 9.4x3x1.6" (240x78x40mm); Weight: 8.4oz (237g)
- Complete with 2 AAA batteries, protective cap, and pouch case
Voltage LED steps | AC: 24, 48, 120, 208, 240, 277, 480, 600 DC: 6, 12, 24, 36, 48, 110, 220, 400 |
ACV frequency range | 50/60Hz |
LED enable input voltage | >4.5V AC/DC |
Accuracy | -30% to 0% of the indication |
Range selection | Automatic |
Max measuring current | ≤1.2mA (600VAC); ≤1.0mA (400VDC) |
Display delay | LED indication <0.1s |
Input Impedance | 1MΩ (approx) |
Continuity test | Range 0 to 400kΩ, guaranteed on < 50kΩ; <10µA test current; |
Low impedance test | 12-250VAC/DC; impedance <6kΩ; |
Operation time | 30 seconds on / 10 minutes off duty cycle |
Power supply | 2 x "AAA" 1.5V alkaline batteries, 50mA max |
Battery life | Approx. 8 hours of continuous use typical |
Operating Temperature | -10 to 55°C (14 to 131°F) |
Storage Temperature | -30 to 60°C (-22 to 140°F) |
Operating Humidity | 10 to 85% RH (non-condensing) |
Operating Altitude | 2000m (7000 ft.) maximum |
Safety | This meter is intended for origin of installation use and protected, against the users, by double insulation per EN61243-3:2010 CATIII 600V and CAT IV 600V. |
Approvals | CE, IP64 |
Dimensions | 240 x 78 x 40mm (9.4 x 3 x 1.6") |
Weight | 260g (9.2oz) |