GasAlertMicroClip XT Sensor Spares and Replacements

BW Technologies Replacement Oxygen (O2) Sensor

The BW Technologies Replacement Oxygen Sensor is a highly effective replacement accessory. It has a sensor range of 0 to 30% with a 0.1% resolution. The replacement sensor is operational in a temperature range of -4 to 122 degrees Fahrenheit. It is compatible with some of the BW Technologies devices. BW Technologies replacement sensors are reliable and dependable and backed by solid performance. To ensure optimal compatibility, please consult your product specification sheet.

Part Number: SRX10C1

SR-H-MC Replacement MICROceL Hydrogen Sulfide (H2S) Sensor

Make sure your monitor is protecting you by routinely changing your H2S sensor. Hydrogen Sulfide is one of the most potent dangers in today's working environment. Always bump check to make sure you are getting accurate readings. If your sensor is slow to respond or doesn't respond at all then replace immediately. Changing the sensor is a fast and easy process, simply open your monitor, slide out the existing sensor, and plug in the new one. Once it is installed you will need to re-calibrate your instrument before use.

SR-M-MC Replacement MICROceL Carbon Monoxide (CO) Sensor

• GasAlertMicroClip
• GasAlertMicroClip XT
• GasAlertMicroClip XL
• GasAlertMax XT
• GasAlertMax XT II

SR-W-MP75C Replacement MICROpeL Combustible (LEL) Sensor

Keeping your gas monitor running smoothly and accurately is a vital task that ensures your safety. By routinely checking your sensors to verify that they are responding to gas is crucial. If you find that your LEL sensor is failing calibration or responding slowly you should immediately replace it. Combustible sensors are often contaminated by various substances in the environment and weaken over time. If this occurs please replace your sensor immediately.

SR-X-MC Replacement MICROceL Oxygen (O2) Sensor

The SR-X-MC is an oxygen sensor made by Honeywell that is used is several instruments. It's body is much smaller than other O2 sensors which allows for a smaller instrument. However, this smaller design also can't contain as much electrolyte as larger designs, therefore the expected lifespan is shorter. Typical oxygen sensors have a lifespan of 2 years, but the SR-X-MC usually lasts around 8-9 months. Fortunately, changing the sensor is an easy task with it's plug in design. After installing please allow 15 minutes for the sensor to stabilize.

Part Number: SRWMCDUM

BW Technologies Dummy Sensor for 3-Pin O2 or 3-Pin Twin Tox Locations

The BW Technologies Dummy Sensor for 3-Pin O2 or 3-Pin Twin Tox Locations is a dummy sensor that acts as a placeholder for the device. This dummy sensor does not detect gases and does not initiate the alarm sequence on the device. The sensor can be used for training and storage purposes. This cost effective dummy sensor fits several BW Technologies products.

Part Number: SRDUMM1

Part Number: SRXMCDUM

Part Number: SRTOXMCDUM

Part Number: MC2SS

MC2-SS-K1 Quad Sensor Screen Filters (kit of 10)

To extend the lifespan of your BW Technologies gas detection instrument, proper inspection and maintenance is required. When inspecting the device, be certain to regularly check the conditions of all filters. A clean filter will help to protect the device by preventing debris, dust, and moisture from entering the device, sensor, or pump. The Quad Sensor Screen Filters are compatible with certain BW Technologies devices (please check your device’s product specifications sheet for compatible) and is available in a pack of 10 screen filters.

Part Number: MCSS

BW Technologies Quad Sensor Screen Filters (kit of 10)

To extend the lifespan of your BW Technologies gas detection instrument, proper inspection and maintenance is required. When inspecting the device, be certain to regularly check the conditions of all filters. A clean filter will help to protect the device by preventing debris, dust, and moisture from entering the device, sensor, or pump. The Quad Sensor Screen Filters are compatible with certain BW Technologies devices (please check your device's product specifications sheet for compatible) and is available in a pack of 10 screen filters.

Part Number: MCSSK1