- All Products
- Shop by Brands
- BW Technologies
- BW Technologies
- BW Technologies Monitors
- Models
- BW Clip
- BW Clip4
- GasAlertClip Extreme
- GasAlert Extreme
- GasAlertMicroClip XT
- GasAlertMicroClip XL
- GasAlertMicroClip X3
- GasAlertQuattro
- GasAlertMax XT II
- GasAlertMicro 5 Series
- SamplerPak
- IntelliDox Docking System
- MicroDock II
- BW Ultra
- BW Solo
- Gas Monitors
- Gas Monitor Manufacturers
- BW Technologies
- Bacharach
- Biosystems
- Crowcon
- Gas Clip Technologies
- GfG Instruments
- GMI/Detcon
- Honeywell Analytics
- Industrial Scientific
- MSA
- RAE Instruments
- RKI Instruments
- Calibration Gas
- Combustion Analyzers
- Water Quality
- Reliability Instruments
- Refractometers
- HVAC
- Weather
- Temperature
- Laboratory
- Sound
- IAQ
- Electrical
- All Categories
Hanna Industrial Grade TDS Controller with Proportional Fertilizer Dosing for Hydroponics Applications, 230V - HI9934-2
Item #:
HI9934-2
Brand:
Hanna Instruments
Share this product:
HI9934-2 Industrial Grade TDS Controller with Proportional Fertilizer Dosing for Hydroponics Applications, 230V by Hanna Instruments
HI 9934 is a wall mounted meter that controls TDS in the 0 to 1999 ppm (mg/L) range through a single set point for dosage of fertilizers. The proportional control can be fine tuned through the time cycle between 0 to 90 seconds and the proportional band from 0 to 400 ppm. Coarse and fine as well as a slope trimmer make for an accurate setting and calibration. A pump or electrovalve can be powered through the terminal. In addition to the set point relay, HI 9934 also provides for an alarm relay. The alarm is activated when the measurements exceed the set point by a user selectable margin in the 50 to 450 mg/L (ppm) range. The alarm also triggers if, due to a malfunction, the continuous dosing time exceeds the operator adjustable period of 1 to 10 minutes. The alarm can be configured in either normally-closed or normally-open position and turned off during maintenance.
HI 9934 also provides an isolated output signal which is user selectable between 0-20 or 4-20 mA.
HANNA instruments four-ring TDS probes with incorporated temperature sensor and DIN connector can be quickly attached to the controller. Readings are automatically compensated for temperature variations in the 0 to 50°C (32 to 122°F) range.
The extractable terminal wiring is through the side of the meter with washers and grommets. The compartment containing the connections is enclosed behind a fire-retardant ABS panel.
Order Information:
HI 9934 is supplied complete with instructions.
Range | 0 to 1999 ppm (mg/L) |
Resolution | 1 ppm (mg/L) |
Accuracy @ 20°C | ±2% f.s. |
Calibration | through "ZERO CAL" and "SLOPE CAL" trimmers |
Setpoint | from 0 to 1999 ppm (mg/L) |
TDS Conversion Factor | 0.65 mg/L (ppm) = 1 µS/cm |
Temperature Compensation |
automatic, 0 to 50°C (32 to 122°F) with ß = 2%/°C |
Recorder Output | selectable at 0-20 mA or 4-20 mA (isolated) |
Proportional Control |
TDS from 0 to 400 ppm and time cycle from 0 to 90 seconds |
Alarm Contact | terminals can be configured as normally open or normally closed (isolated output max. 2A, max. 240V, resistive load, 1,000,000 strokes). The alarm is activated if TDS exceeds by more than the user- selectable interval (0 to 400 ppm) from the set point or due to overdosage |
Dosing Terminals | relay (115 to 240V, max.2A, 1,000,000 strokes) are activated whenever TDS falls below the set point |
Probe | four-ring potentiometric with built-in temperature sensor (not included) |
Power Supply | ±10% 115 VAC or 230 VAC; 50/60 Hz |
Environment | -10 to 50°C (14 to 122°F); RH max 95% non-condensing |
Case Material | fiber-reinforced, self-extinguishing ABS |
Dimensions | 221 x 181 x 86 mm (8.7 x 7.1 x 3.4’’) |
Weight | 1.6 kg (3.5 lb.) |